Register Our Newsletter
Hongsonic is the China first onsite installation ultrasonic cleaner factory, covering over 100 countries. You can always rely on our stable team!
10L gun ultrasonic cleaner can allow you to clean couple of handguns together. You can choose five different function series here.. If you still have questions about what you need to choose, please feel free to contact our sales team.
|Single Packing Size||
0~30 Minutes Setting
20 GP:536pcs/40 GP:1100pcs
Preparing Ultrasonic Cleaner For Cleaning Firearms:
Step 1: Check that ultrasonic cleaner tank is clean. Wipe out any residue.
Step 2: Fill ultrasonic cleaner tank with cleaning solution.
Step 3: Turn on heater and set to recommended temperature. Allow enough time for cleaning solution to come to temperature. If the ultrasonic cleaner doesn’t have a display that shows that actual temperature, use a thermometer. Keeping the tank covered will speed up heating.
Step 4: Degas the cleaning solution (Not necessary if previously done to this batch of cleaning solution or lubrication solution)
Steps For Ultrasonic Cleaning A Firearm:
Step 1: Field strip the firearm.
Step 2: Swab the bore with a good defouler and allow to soak for a few minutes, then run a bore brush several passes through.
Step 3: Place the firearm in the basket. Be sure to also use a plastic tray to prevent direct contact between the firearm and metal basket.
Step 4: Lower the basket into the ultrasonic cleaner bath.
Step 5: Set cleaning time (5 to 30 minutes depending on how dirty the firearm is) and turn on ultrasonic cleaner.
Step 6: Check firearm periodically for cleanliness.
Step 7: When clean, turn off ultrasonic and heater.
Step 8: Lift the basket from the tank. Allow a few seconds for excess cleaning solution to drain back into the tank.
Step 9: Rinse each part with water (or whatever is recommend). If water is recommended, using warm water will speed drying. If you are using a solvent based cleaning solution, rinsing may not be required and you may only need to set the firearm aside to air dry.
Step 10: Blow off as much water as possible with an air compressor or canned air. Pay special attention to confined spaces where water may be trapped.
Step 11: ALWAYS IMMEDIAELY LUBRICATE FIREARMS AFTER CLEANING! (See following Section)
Steps For Lubricating A Firearm:
If you are using a single-tank ultrasonic system, you will need to remove the cleaning solution, clean the tank, and replace it with lubricating solution. If heating is required, allow lubricating solution to come to temperature before proceeding.
Step 1: Ensure that the firearm has been thoroughly rinsed and as much excess water as possible has been removed.
Step 2: Place the firearm in the basket. Be sure to use a plastic tray to prevent direct contact between the firearm and metal basket.
Step 3: Lower the basket into the ultrasonic cleaner bath.
Step 4: Set cleaning time to 5 minutes and turn on ultrasonic cleaner.
Step 5: Turn off ultrasonic (and heater if used).
Step 6: Lift the basket from the tank. Allow a few seconds for excess lubricating solution to drain back into the tank.
Step 7: Wipe down all parts with a clean cloth to absorb excess lubricating solution. Do not wipe excessively as you want to leave a thin coating of lubricant on the parts. Use an air compressor or canned air to blow excess lubricating solution out of confined spaces.
Step 1: Thoroughly inspect all parts. As they will be very clean, now is the best time to inspect for wear, cracks or other problems and take corrective action.
Step 2: Lubricate all points as recommended by the firearm manufacturer using the appropriate lubricants. The lubricating solution alone may not be the best choice for all lubrication points.
Step 3: Complete firearm assembly according to the manufacturer’s instructions.
Brief Introduction Of 10L Ultrasonic Cleaner:
10L ultrasonic cleaner is a helpful cleaning tool for your dirty parts. It has 360W ultrasonic power which can handle the normal cleaning job. Besides we have five different series for you to choose.
You might want to know what is degas function and what is sweep frequency function. Please check below:
Degas: Degas function can drive out gas in cleaning liquid which will absorb ultrasonic energy.
Sweep frequency: Sweep frequency technology to ensure uniform levels of ultrasonic activity throughout the fluid, these baths offer high performance giving an accurate and precise ultrasonic process. It can avoid the hot spot on the cleaning object.